Main Products:
Induction HeaterInduction heating control board
Induction water heater
Induction hot blast stove
Induction heater coil
Induction Steam Generator
Cabinet type induction heater
What is Induction Heating?
Induction heating can basically be considered as electromagnetic heating. In induction heating process, eddy currents are produced in the heated material using the electromagnetic induction principle and the heating of the material is carried out in a contactless manner.
Hence, heating is much more efficient than traditional resistances since heat is produced inside the working material. In other words, heat losses are reduced by induction heating, thus increasing the total heating efficiency.
Product Description
Technical advantages of Jiangxin electromagnetic heating control cabinet:
1. The world famous German Yingfei IGBT frequency conversion module is adopted to ensure the stability of the product.
2. High speed DSP phase-shifting algorithm is adopted, and each output cycle is accurately calculated to achieve the purpose of energy saving.
3. Magnetic isolation drive technology solves the interference problem caused by optical coupling drive.
4. Strong adaptability to environment and can be used in harsh environment.
5. The system control power supply adopts multi-level EMI suppression to ensure better power supply under harsh power conditions
6. Strong anti-interference ability, up to more than 50MW, combined parallel operation and reliable operation.
7. The coil to ground protection function can effectively protect the whole system and ensure safe use when the coil is broken or the coil is short circuited to the ground.
8. It can be customized for water cooling and air cooling. The cooling fan is a famous delta high-speed DC fan to escort the cooling system of the controller.
9. The incoming and outgoing lines of the power supply adopt copper strip structure and pure copper high current terminals to ensure that the copper strip and terminals do not heat when they are over operated.
Application:
| Plastic rubber industry |
Such as: electromagnetic heating projects, rubber machines, pelletizers, vulcanizers, extruders; |
| Pharmaceutical and chemical industry |
Such as: medical machinery steam sterilizers, medical infusion bags, plastic equipment production lines, liquid heating pipelines in the chemical industry, etc . |
| Energy and food industry |
Such as: heating of crude oil transportation pipelines, food machinery, hot air pipeline drying furnaces, tea processing equipment and other equipment that requires electrical heating |
| Building materials industry |
gas pipe production line, plastic pipe production line, PE plastic hard flat net, geonet net unit, automatic blow molding machine, PE honeycomb board production line, single and double wall corrugated pipe extrusion production line, composite air cushion film unit, PVC hard Tube, PP extrusion transparent sheet production line, extruded polystyrene foam tube, PE winding film unit; |
| Energy saving reconstruction |
Aluminum-plastic plate roller oven electromagnetic heating project, energy-saving transformation of various plastic machines, etc. |
Detailed Photos
Plastic granulator induction heater 80kw Electromagnetic Control Cabinet - Thermal Oil Electromagnetic Heating Equipment
1,Connect the power supply voltage of the cooling fan, but connect the 220V power when the fan is 220V, and connect the 380V power when the fan is 380V
2,Connected with cooling fan 220V / 380V (depending on the user, generally 380V)
3,When the external cooling fan is DC 24V, this interface is a switch that controls the 24V fan to work or stop. The two ends of the interface are actually the normally closed contact points of the relay output on the motherboard.
4,Dual AC 24V power supply (choose 4 or 5 when making half bridge)
5,Dual AC 24V power supply (choose 4 or 5 when making half bridge)
6,Single AC 16V power supply
7,Power indicator (red)
8,Work indicator light, flashing during standby, and always on (green) during work
9,External indicator light, led to the LED interface outside the chassis
10,The soft start interface is connected to the R / s interface outside the chassis (can be set to open or close work through F-20, factory default close work, open stop status
11,Finely adjust the power potentiometer. When there is a large deviation in power, this potentiometer can be adjusted appropriately.
12,32-bit high-speed DSP processor
13,Externally connected programmable operating display
14,Isolated RS485 communication interface
15,External load temperature detection interface 1, with accuracy of ± 1 ° C (maximum 150 ° C) single channel, default 1 is used to measure external working temperature
16,External load temperature detection interface 2, with accuracy of ± 1 ° C (maximum 150 ° C)
17,Multi-function input interface (set by F-20)
(1)10K input for external connection potentiometer, can adjust the power range from 20% to 100%
(2)Externally connected PID input (0 ~ 5V) input
Do infrared thermometer or thermocouple conversion voltage 0 ~ 5V input to achieve the display temperature and control power size (up to 1000ºC can be measured and displayed)
18,Connect the high-frequency Mutual inductor and pay attention to the direction. If the direction is reversed, the power is very small
19,IGBT module drive (when doing half bridge, choose 19, 20 or 23, 24)
20,IGBT module drive (when doing half bridge, choose 19, 20 or 23, 24)
21,Connected to high voltage DC bus
22,IGBT temperature sensor interface
23,IGBT module drive (when doing half bridge, choose 19, 20 or 23, 24)
24,IGBT module drive (when doing half bridge, choose 19, 20 or 23, 24)
25,Connected to high voltage DC bus
26,RS485 communication interface, connect A ,B
27,Externally connected K-type thermocouple
28,Externally connected 12V relay drives other required loads, synchronized with the fan start / stop of the machine
FAQ
Q: Are you trading company or manufacturer ?
A: We are factory.
Q: How long is your delivery time?
A: Generally it is 10 days if the goods are in stock. or it is 40 days if the goods are not in stock, it is according to quantity.
Q: Do you provide samples ? is it free or extra ?
A: provide. Charge according to the retail price of the product.
Q: What is your terms of payment ?
A: Payment:30% T/T in advance ,Pay in full before shipment.
Q:What other products does the company have?
A:Electromagnetic heater, electromagnetic steam generator, Electromagnetic hot blast furnace
Audited Supplier 
){kind=link}